Hi mkiz,

which rooms do you see when you oben the Room Editor (press button "SELECT VENUE")?

If there's only the default room available, Mir SE probably does not know the proper path to your Mir Data files. You can change this path
in the Preferences Dialog ("Options" -> "Preferences") - make sure it points to the *.vmi files of the room pack.

Hth, Florian

 Florian,

I see the default room and the Mozartsaal (I believe it says 3rd row?).  When I switch from the default room to the Mozartsaal venue, the middle of the MIR SE interface turns into a blank white space.  I can add instruments, and they appear against the blank white background.

thanks.

mkiz

It's just a guess, but for me this sounds like your video-card has a hard time fulfilling OpenGL 2.1 standards :-) ... MIR system requirements say "DirectX 10-capable video card with support for OpenGL 2.1"

You could try to decrase the "Venue Image Detail Level" to a lower value (Options > Preferences > General). This could be a workaround for the issue you're facing.

HTH,

 Dietz,

You were right!  I updated the drivers for my video card, and now I can see the Vienna Konzerthaus Mozartsaal v2 with the 3rd row mic position.

Wonderful!

mkiz

 Dietz,

One final question--how does one get third party vsts to show up in the instrument selection option list described in the manual? I have some non-VSL instruments that I would like to test in MIR SE, but I have scoured the manual and the forums and cannot figure out how to add a third party VSTi.  The manual is clear about VST effects, and I can see where to add those in the interface, but it how do I point MIR to the right location to find third party VSTi's?

Thanks,

Mkiz 

VSTi's are handeled like VST-plugins, they are just listed (and selected) differently. It's on p. 33 of the MIR manual:

"Preferences > Plug-ins: Shows a list of VST (not VSTi) plug-ins available to MIR. Clicking on
the VST Settings … button allows you to browse attached hard disks for folders
with installed plug-ins [VSTi's too!] and add them to the list. Alternatively, you may remove
folders from the list, or rescan selected folders for recently added plug-ins.

IMPORTANT! Only VST effect plug-ins are shown in this list. All valid 3rd party
VSTi’s (VST instrument plugins) appear in the “Source”-pulldown of the “Add
Instrument”-window (see section C 2.1)

CAUTION: Only 64-bit compatible VST2 plug-ins will do! Be careful when adding new plug-ins to the list, as there always is the
possibility of some unforeseen conflict halting the whole system.

HINT: With the help of so-called VST wrappers like jBridge7 it is principally possible to use 32-bit plug-ins in a 64-bit environment
like MIR. In many cases, this will work wonderfully, and significantly increase the number of possible audio plug-ins. However, we
hope you will understand that we do not (cannot) actively support this special workaround."

HTH,

 Dietz,

I read all this in the manual, but I guess I was confused.  The section you reference here is still confusing me:

IMPORTANT! Only VST effect plug-ins are shown in this list. All valid 3rd party
VSTi’s (VST instrument plugins) appear in the “Source”-pulldown of the “Add
Instrument”-window (see section C 2.1)

My EWQL VSTs are not appearing, in the source pulldown, so I assume that I need to set some pointer in MIR so that it knows where to look for them.  I realize that I cannot select VSTis in this preferences window, but apparently I add VSTis here so that they will then appear in the "add instrument"  source pulldown selector?  And once added, they will still not appear in this preferences>plugins window. 

Sorry for my confusion.  I am usually not so dense! [:)]

 Three questions:

1. Have you "told" MIR where your VSTi folder is?
2. Are you sure that your VSTi players are all 64bit?
3. Are you talking about Kontakt or PLAY?

DG

 DG,

I don't know how to :"tell" MIR where the VSTi fiolder is...that is what I am trying to find out.

I cant see PLAY, which is the one 64-bit VSTi that I have that I am most interested in seeing.

Thanks,

mkiz

So, have you tried:

Options/Audio settings/Plugins/VST settings/Add folder

As long as PLAY is in the folder that you "add" and is the 64bit version, MIR should be able to load it. Just make sure that all your software is up-to-date.

DG

 DG,

Thanks.  This worked.  What was throwing me off is that the folder appears empty even though the 64 bit VSTi is in it.  But, sure enough, when I added the folder, even though nothing appears added in this audio plugins section, the Play instrument become available in the Add instrument selector pulldown. 

Play doesn't seem to work very well here on this particular machine, but I know I am underpowered, since it is a Core 2 Quad running at 2.4GZ, with 8GB Ram on Vista 64bit OS.  I am just trying to see what the sounds are like to decide whether to buy new machine specifically to run MIR SE.  I guess I am just going to have to jump in with both feet and hope it works well!

Thanks for your tip.

mkiz