[TEST UPDATE]

I just loaded 4 new instances, but only used three.

I loaded Oboe, Flute and ClarinetB

Each wind had loaded

Staccato
Short Portato
Medium Portarto
Long Portato
Sustain
Legato Normal

I had about 137MB left

There was appearently no problem with playback, but I dident test it thoroughly. Bare in mind also that this test was done on a slave machine. On my main Daw I only have a little over 1GB left for samples after cubase is loaded. However that would still be enough to load all the solo strings with the articulations I mentioned.

@Christian Marcussen said:

Bare in mind also that the legatos have both p and f layers loaded, and that each of the other articulations have 2 versions of each note loaded. Personaly I find it pretty impressive

That's really impressive! Thanks so much for checking it out.

Actually what I was thinking is, since I am goning to buy a new machine (have 2 at the moment) so I can spread my orchestral work to 3 computers for each dedicated section (strings, brass and wind with percussion staggering around hehe). Instead of needing to go through the god-knows-what-will-happen-when-you-install-GS3 route, I might as well have the new host running with VSTi only. Was thinking strings coz it seems it would need the fewest instances to load up among the 3 families.

Thanks again! [[;)]]
Frankie

Thanks Christian for the infor. Very impressive. With 4 slaves and Host It sounds like 'freezing' will not be necessary in all but the biggest projects/arrangements.

Still have to sort out how to deal not having GP (during writing stage). What are you going to do on this?

I still have to pick up VStack - was that a clean install and setup?


Thanks for all the 'advance look' for us poor saps that can only dream about it (still waiting for Illio to ship).


Rob

Setting up V-stack is no prob. As long as you have MOL installed, V-stack fits right in.

Still dont have a verb solution yet.

@Christian Marcussen said:

Setting up V-stack is no prob. As long as you have MOL installed, V-stack fits right in.

Still dont have a verb solution yet.

Sorry Chrisitan, what is "MOL"? I'm going to have to get VStack for my PC, and as a Mac guy (I use Mac for sequencing and Pro Tools) I'm a little slow on the PC side of things...[;)]

Tom

@tom@aerovons.com said:

Sorry Chrisitan, what is "MOL"? Tom

MIDI over LAN

DG

www.musiclab.com

They have a program called Mide OverLan (MOL) which allows you to send midi signals over your network to any computers you may have.

Daft question...is Midi Over Lan available for Mac users or is it just for Windows?

So many things to learn... [[;)]]

Looks cool, but I don't see it's advantage for a simple two computer setup like I have. I record on the Mac, and take a MIDI out to the PC. Done...[;)]

TH

It is cross-platform, so that your DAW can be a Mac or a PC and your slaves can also be either. Where it can be useful is that you don't need to connect a MIDI device to use a Giga (for example) PC with a Mac sequencer, and the MIDI timing is tighter than any hardware device.

DG

@jamriding said:

Daft question...is Midi Over Lan available for Mac users or is it just for Windows?

So many things to learn... [[;)]]

I beleive the new version called MolCP supports mac. I think the CP stands for Cross Platform.

@DG said:

It is cross-platform, so that your DAW can be a Mac or a PC and your slaves can also be either. Where it can be useful is that you don't need to connect a MIDI device to use a Giga (for example) PC with a Mac sequencer, and the MIDI timing is tighter than any hardware device.

DG

Yes, I have timing problems a lot with Giga, especially if I dare do any drums.

I'm embarassed to say I'm really dumb about this, I read the manual on this but....I need some kind of network cable going from somewhere out of the PC to the Mac...right? [;)]

Gee this is silly I know but I have not messed with networks. My Mac is connected to DSL and that's about as far as I've gone...

Thanks for any help in setup.

Tom

@jamriding said:

Daft question...is Midi Over Lan available for Mac users or is it just for Windows?

So many things to learn... [[;)]]

I beleive the new version called MolCP supports mac. I think the CP stands for Cross Platform.
See, your posting fingers are getting slow; I beat you to it again [:D]

DG

@DG said:

It is cross-platform, so that your DAW can be a Mac or a PC and your slaves can also be either. Where it can be useful is that you don't need to connect a MIDI device to use a Giga (for example) PC with a Mac sequencer, and the MIDI timing is tighter than any hardware device.

DG

Yes, I have timing problems a lot with Giga, especially if I dare do any drums.

I'm embarassed to say I'm really dumb about this, I read the manual on this but....I need some kind of network cable going from somewhere out of the PC to the Mac...right? [;)]

Gee this is silly I know but I have not messed with networks. My Mac is connected to DSL and that's about as far as I've gone...

Thanks for any help in setup.

Tom

You're not on your own Tom, but this one i know just enough about to maybe help.

You'll need a free network card in each machine, and a normal network cable.
Once MOL (Midi over a Local area Network, which is what you'll create when you cable one comp to another) is installed, follow the instructions.

I'm sure others will chime in if this is wrong.

Regards, and good luck,

Alex.

Just in case anyone's interested MIDI over Lan is built into OS X. Have a look at the Utility "Audio MIDI Setup" and double click on the network Icon. I think this is only 10.4 and above.

Regards

Dave Hage

As a matter of interest, can I route MOL through a router to a second PC?

Andy O'Callaghan

My setup is through a router which then enters a hub (since I only have 4 exists from my router and need 6). So yes - no problem in using a router if I understand you correctly. If you can set your computers up in a network, then you can use MOL.

as a proof of concept i routed MoL even through the internet to a machine controlled by remote desktop - very funny [;)]
you just have to make sure the respective port (usually 11 000 UDP) is not blocked on the router (and of course also not by a local firewall)
christian